博碩士論文 etd-0709103-161905 詳細資訊


[回到前頁查詢結果 | 重新搜尋]

姓名 榮必彰(Bi-Jang Rung) 電子郵件信箱 bance@ms65.hinet.net
畢業系所 機械與機電工程學系研究所(Mechanical and Electro-Mechanical Engineering)
畢業學位 碩士(Master) 畢業時期 91學年第2學期
論文名稱(中) 歪斜軸齒輪組接觸分析之研究
論文名稱(英) A Study on the Tooth Contact Analysis
of Gear Sets with Skew Axes
檔案
  • etd-0709103-161905.pdf
  • 本電子全文僅授權使用者為學術研究之目的,進行個人非營利性質之檢索、閱讀、列印。
    請遵守中華民國著作權法之相關規定,切勿任意重製、散佈、改作、轉貼、播送,以免觸法。
    論文使用權限

    電子論文:校內立即公開,校外一年後公開

    論文語文/頁數 中文/89
    統計 本論文已被瀏覽 5598 次,被下載 6889 次
    摘要(中) 摘要
    歪斜軸齒輪組目前已被廣泛的應用,尤其以蝸桿蝸輪組與戟齒輪組為最。本研究使用齒面接觸分析法(Tooth Contact Analysis)建構具有裝配誤差的線接觸型態之歪斜軸共軛齒形模式。同時分析其齒面構成參數對傳動誤差造成的影響,並以複雜形法(Complex Method)優選出在有裝配誤差的狀況下具有最佳的傳動誤差的齒輪建構參數。並以此優選參數建構實體模型,再以電腦模擬軟體分析其接觸時的特性以玆驗證。
    摘要(英) ABSTRACT
    Presently, many industrial applications of gear sets with skew axes, especially worm gear and hypoid gear, are most widely used. The main content of this thesis is to construct the contact analysis model of the line-contacted type tooth profile of gear sets with skew axes with assembly error. The influence of geometrical parameters of skew-axes gear to the transmission error is analyzed. The complex method for optimization is implemented to select the better skew-axes gear parameters with the best performance in transmission error with assembly error. To prove the presented analysis model, the optimized gear parameters are utilized to construct the solid model for analyzing the contact properties by using computer simulation program.
    關鍵字(中)
  • 傳動誤差分析
  • 齒接觸分析
  • 歪斜軸齒輪
  • 關鍵字(英)
  • transmission error
  • gear with skew axes
  • tooth contact analysis
  • 論文目次 目錄
    目錄 I
    圖目錄 III
    表目錄 V
    摘要 VI
    ABSTRACT VII
    符號說明 VIII
    第一章 緒論 1
    1-1 前言 1
    1-2 文獻回顧 2
    1-3 研究方向與論文結構 4
    第二章 歪斜軸齒輪組共軛齒形之數學模式及求解 6
    2-1 歪斜軸齒輪組共軛齒形之座標系統定義 6
    2-2 瞬間螺旋軸位置參數及N平面 9
    2-3 齒面嚙合拘束方程式之推導與求解 18
    2-4 歪斜軸齒輪組共軛齒面的建構 23
    第三章 具裝配誤差的歪斜軸齒輪組之傳動誤差分析 27
    3-1 具裝配誤差的歪斜軸齒輪組之座標系統 27
    3-2 具裝配誤差下的歪斜軸齒輪組之傳動誤差 29
    3-2-1無裝配誤差下的齒廓曲面 29
    3-2-2具裝配誤差下的新接觸點 31
    3-2-3接觸點求解及傳動誤差 34
    3-3 具裝配誤差對傳動誤差的影響 37
    第四章 歪斜軸齒輪組建構參數最佳化 41
    4-1 歪斜軸共軛齒面建構 41
    4-2 歪斜軸齒輪建構參數最佳化 45
    4-2-1 具裝配誤差下齒輪建構參數對裝配誤差的影響 46
    4-2-2 齒輪建構參數 49
    4-2-3 複雜形法 50
    4-2-4 齒輪建構參數最佳化 53
    4-3 改變最佳化條件的其它歪斜軸齒輪組最佳建構參數 57
    4-3-1 固定設計參數:轉速比 57
    4-3-2 固定設計參數:扭角 62
    4-3-3 固定設計參數:中心距 63
    第五章 歪斜軸齒輪組之建構與接觸分析 64
    5-1 歪斜軸齒輪組實體建構 64
    5-2 歪斜軸齒輪組運轉模擬 72
    5-2-1無裝配誤差下的歪斜軸齒輪組運轉模擬 72
    5-2-2 具裝配誤差下的歪斜軸齒輪組運轉模擬 74
    5-3 改變最佳化條件的其它歪斜軸齒輪組實體建構 78
    第六章 結論 85
    參考文獻 86
    參考文獻 參考文獻
    1.  Bibel, G. D., and Handschuh, R., 1997, “Meshing of a Spiral Bevel Gear Set with 3-D Finite Element Analysis,” Gear Technology, Vol. 14, pp. 44-47. 
    2.  Claude, G., and Thierry, G., 2000, “Simulation and Experimental Measurement of the Transmission Error of Real Hypoid Gears Under Load,” ASME Journal of Mechanisms Design, Vol. 122, pp. 109-122.
    3.  Chang, H. L., 1992, A Study of Parametric Tooth Profiles for Spur Gears and Bevel Gears, Ph.D. Dissertation, National Sun Yat-Sen University, Kaoshiung, Taiwan, R.O.C.
    4.  Chang, H. L., and Tsai, Y. C., 1991, “An Investigation on the Design Space for Parametric Tooth Profiles,” Proceedings of the 8th World Congress on the Theory of Machines and Mechanisms, Prague, pp. 539 – 542.
    5.  Chang, H. L., and Tsai, Y. C., 1992, “A Mathematical Model of Parametric Tooth Profiles for Spur Gears,” ASME Journal of Mechanical Design, Vol. 114, No. 1, pp. 8–16.
    6.  Colbourne, J. R., 1982, “The Kinematics of Crossed Helical Gears,” ASME Journal of Mechanical Design, Vol. 104, No. 1, pp. 83–89.
    7.  Dareing, D. W., and Chen, C. M., 1973, “Kinematics and Evaluation of Flat-Toothed Hypoid Gears,” ASME Journal of Engineering for Industry, Vol. 95, No. 4, pp. 1171–1177.
    8.  Hunt, K. H., 1978, Kinematic Geometry of Mechanisms, Clarendon Press, Oxford.
    9.  Janninck, W. L., 1988, “Contact Surface Topology of Worm Gear Teeth,” Gear Technology, March/April, pp. 31-47.
    10. Jehng, W. K., 1999, A Study of the Tooth Profiles of Gear Sets with Skew Axes, Ph.D. Dissertation, National Sun Yat-Sen University, Kaoshiung, Taiwan, R.O.C.
    11. Jehng, W. K., and Tsai, Y. C., 1998, “Curvature Analysis and Synthesis of Skew Gear Sets with Kinematic Parametric Models,” Transactions of the Canadian Society for Mechanical Engineering, Vol. 22, No. 4A, pp. 341–368.
    12. Jehng, W. K., and Tsai, Y. C., 1999, “Kinematics Parametric Method to Generate New Tooth Profiles of Gear Sets with Skew Axes,” Mechanism and Machine Theory, Vol. 34, No. 6, pp. 857–876.
    13. Lauwerier, H. A., and Koiter, W. T., 1978, Applied Mathematics and Mechanics, North-Holland Publishing Company, Oxford.
    14. Litvin, F. L., 1989, Theory of Gearing, NASA Reference Publication, 1212, AVSCOM Technical Report, 88-C-035.
    15. Litvin, F. L., 1994, Gear Geometry and Applied Theory, PTR Prentice Hall, Inc., Englewood Cliffs, New Jersey.
    16. Litvin, F. L., Chaing, W. S., Kuan, C., Lundy, M., and Tsung, W. J., 1991b, “Generation and Geometry of Hypoid Gear-Member with Face –Hobbed Teeth of Uniform Depth,” International Journal of Machine Tools and Manufacture, Vol. 31, No. 2, pp. 167–181.
    17. Litvin, F. L., and Gutman, Y., 1981a, “Methods of Synthesis and Analysis for Hypoid Gear-Drives of “Formate” and “Helixform” –part 1. Calculations for Machine Settings for Member Gear Manufacture of the Formate and Helixform Hypoid Gears,” ASME Journal of Mechanical Design, Vol. 103, No. 1, pp. 83–88.
    18. Litvin, F. L., and Gutman, Y., 1981b, “Methods of Synthesis and Analysis for Hypoid Gear-Drives of “Formate” and “Helixform” –part 2. Machine Setting Calculations for the Pinions of Formate and Helixform Gears,” ASME Journal of Mechanical Design, Vol. 103, No. 1, pp. 89–101.
    19. Litvin, F. L., and Gutman, Y., 1981c, “Methods of Synthesis and Analysis for Hypoid Gear-Drives of “Formate” and “Helixform” –part 3. Analysis and Optimal Synthesis Methods for Mismatch Gearing and Its Application for Hypoid Gears of “Formate” and “Helixform”,” ASME Journal of Mechanical Design, Vol. 103, No. 1, pp. 102–113.
    20. Litvin, F. L., and Kin, V., 1992, “Computerized Simulation of Meshing and Bearing Contact for Single-Enveloping Worm-Gear Drives,” ASME Journal of Mechanical Design, Vol. 114, No. 2, pp. 313–316.
    21. Litvin, F. L., and Lu, J., 1993, “Computer Simulation of Generation Meshing and Contact of Double Circular-Arc Helical Gears, ”
    Mathematical and Computer Modeling, Vol.18, pp. 31-41.
    22. Litvin, F. L., Petrov, K. M., and Ganshin, V. A., 1974, “The Effect of Geometrical Parameters of Hypoid and Spiroid Gears on Its Quality Characteristics,” ASME Journal of Engineering for Industry, Vol. 96, No. 1, pp. 330–334.
    23. Litvin, F. L., Zhang, Y., Lundy, M., and Heine, C., 1988, “Determination of Settings of a Tilted Head Cutter for Generation of Hypoid and Spiral Bevel Gears,” ASME Journal of Mechanisms, Transmissions, and Automation in Design, Vol. 110, No. 4, pp. 495–500.
    24. Litvin, F. L., and Zhang, J., 1989a, “Topology of Modified Helical Gears and Tooth Contact Analysis (TCA) Program ”, NASA Contractor Report 4224(AVSCOM 89-C-002).
    25. Millman, R. S., and Parker, G. D., 1977, Elements of Differentical Geometry, Prentice-Hall, Inc., Englewood Cliffs, New Jersey.
    26. Mohana, R., Rama, C., and Muthuveerappan, G., 1993, “Finite Element Modeling and Stress Analysis of Helical Gear Teeth,”Computer and Structures, Vol. 49, No. 6, pp. 1095-1109. 
    27. Nakada, T., and Yoshimoto, I., 1973, “Design Formula for Involute Profile Shifted Gears Applied to a Skew Shaft Gear-Box,” Mechanism and Machine Theory, Vol. 8, No. 3, pp. 325–338.
    28. Sakai, T., and Maki, M., 1974, “An Investigation on Secondary Action on Skew Gears,” ASME Journal of Engineering for Industry, Vol. 96, No. 1, pp. 25–32.
    29. Sung, L. M., 1995, A Study on the Parametric Conjugate Tooth Profiles of Gear Sets with Skew Axes, Ph.D. Dissertation, National Sun Yat-Sen University, Kaohsiung, Taiwan, R.O.C.
    30. Tsay, C. B., 1988, “Helical Gears with Involute Shapes Teeth: Geometry, Computer Simulation, Tooth Contact Analysis, and Stress Analysis,” ASME Journal of Mechanisms, Transmission and Automation in Design, Vol. 110, pp.482-491.
    31. Tsay, C. B., 1994, “A Study on the Contact of W-N Gear,” Journal of Chinese Society of Mechanical Engineers, Vol. 15, No. 2,pp. 109-117.
    32. Tsay, C. B., and Fong, Z. H., 1989, “Tooth Contact Analysis for Helical Gears with Pinion Circular Arc Teeth and Gear Involute Shaped Teeth,” ASME Journal of Mechanisms, Transmission and Automation in Design, Vol. 111, pp. 278-284.
    33. Tsay, C. B., and Fong, Z. H., 1991, “Computer Simulation and Stress Analysis of Helical Gears with Pinion Circular Arc Teeth and Gear Involute Teeth,” Mechanism and Machine Theory, Vol. 26, No. 2, pp. 145-154.  
    34. Tsay, C. B., Chen, J. L., and Tseng, C. H., 1999, “Tooth Contact Analysis of the Involute Spur Planetary Gear Train,” Journal of Chinese Society of Mechanical Engineers, Vol. 20, No. 4, pp. 317-324.
    35. Tsay, C. B., Sheu, W. L., and Wu, C. H., 1990, “Spur Gears with Crowned Teeth,” Journal of Chinese Society of Mechanical Engineers, Vol. 11, No. 2, pp. 121-133.
    36. Tsai, Y. C., and Sung, L. M., 1993, “A Kinematic Study for Gear Sets with Skew Axes,” Journal of Applied Mechanisms and Robotics, Vol. 1, No. 1, pp. 36–44.
    37. Yang, U. F., 2001, A Study on the Tooth Geometries of Gear Sets with Skew Axes, MSc. Thesis, National Sun Yat-Sen University, Kaoshiung, Taiwan, R.O.C.
    38. Zhang, Y., and Fang, Z., 1999, “Analysis of Tooth Contact and Load Distribution of Helical Gears with Crossed Axes,” Mechanism and Machine Theory, Vol. 26, No. 34, pp. 41-57.
    39.張永爵譯,1998,齒輪的設計與製造(上),徐氏基金會,台北。
    40.沈頌文譯,1998,齒輪的設計與製造(下),徐氏基金會,台北。
    41.劉惟信,2000,機械最佳化設計(第二版),全華圖書,台北。
    42.莊勝雄譯,1995,工程最佳化:方法與應用,國立編譯館,台北。
    口試委員
  • 光灼華 - 召集委員
  • 張慧隆 - 委員
  • 蔡穎堅 - 指導教授
  • 口試日期 2003-06-26 繳交日期 2003-07-09

    [回到前頁查詢結果 | 重新搜尋]


    如有任何問題請與論文審查小組聯繫